Wednesday, August 20, 2008
Softrock on order
I ordered a Softrock Lite v8.3 yesterday. Now I'm getting all excited, waiting for it to arrive! Looking to make a 28MHz IF panadapter.
Sunday, June 29, 2008
June ARRL VHF QSO party
Had a mixed bag up at Mt Greylock. Broke more stuff than I'm worth. Better luck next time I guess. Didn't get rained on too much, and several folks stepped up to make hot meals. Thanks!
Sunday, June 01, 2008
Preparing to contest
Getting ready to go contesting again. First blog in a while, oh well. My watch battery died (odd segué, what?) so I went to Wal-Mart (ugh) to get a new CR2016. Of course they only come in 2 packs. Anyway, while there I got a devilish idea on how to pack radios for the trip.
Meandered over to the craft aisles, looking for foam. My wife is an evil crafting genius, but I, not so much. And so I pushed and prodded and squeezed packages of foam and batting and filling trying to figure out what I could use as an ersatz Pelican case with pluck 'n' place. I'm a ham. I'm cheap. :-)
Settled on a 4-pack of Morning Glory Foam Seat Cushions; 16 inches square by 1 inch thick. 100% premium urethane foam. Under $8.

With that in hand I wandered over to the kitchen/household goods aisle where I started looking for containers. Found a couple of candidates that looked large enough to hold my goodies but small enough so the gear wouldn't rattle about in transit. Found that a Rubbermaid Handi-Box size S (14x10.5x4 inch, or 7.2 qt) snap case box is a very good fit for an Icom IC-706MKIIG, microphone, power cable and some coaxial adapters. Used one of those electronic labellers to mark the outside with the contents (an instant inventory) and cut the foam with normal scissors as padding and it looks great!

I cut a single block for the bottom, with strips for the sides. A small pad goes over the top of the mic and a larger one over the radio. The lid closes and slightly compresses the foam. The radio doesn't rattle a bit. I made up 3 cases all told for various gear... the FT-290RII with battery pack, the 30A power supply, Bencher BY-1 paddle, K1EL Winkey 2 keyer, cables, headphones, etc. Very nice and the total cost was about $20!
Meandered over to the craft aisles, looking for foam. My wife is an evil crafting genius, but I, not so much. And so I pushed and prodded and squeezed packages of foam and batting and filling trying to figure out what I could use as an ersatz Pelican case with pluck 'n' place. I'm a ham. I'm cheap. :-)
Settled on a 4-pack of Morning Glory Foam Seat Cushions; 16 inches square by 1 inch thick. 100% premium urethane foam. Under $8.
With that in hand I wandered over to the kitchen/household goods aisle where I started looking for containers. Found a couple of candidates that looked large enough to hold my goodies but small enough so the gear wouldn't rattle about in transit. Found that a Rubbermaid Handi-Box size S (14x10.5x4 inch, or 7.2 qt) snap case box is a very good fit for an Icom IC-706MKIIG, microphone, power cable and some coaxial adapters. Used one of those electronic labellers to mark the outside with the contents (an instant inventory) and cut the foam with normal scissors as padding and it looks great!
I cut a single block for the bottom, with strips for the sides. A small pad goes over the top of the mic and a larger one over the radio. The lid closes and slightly compresses the foam. The radio doesn't rattle a bit. I made up 3 cases all told for various gear... the FT-290RII with battery pack, the 30A power supply, Bencher BY-1 paddle, K1EL Winkey 2 keyer, cables, headphones, etc. Very nice and the total cost was about $20!
Sunday, March 09, 2008
Catch-up
Grr. Trying to catch up on blogging. Been having issues with the PC, suspect my new PSU, imagine that. Ah well. I did a bunch of work to document the KJ1K/R effort this past January 2008, but it got lost in the bit bucket and I'm too lazy to do it again. :- ) We went, had a good time. Need to work out a better way to coordinate multiple stations moving up the bands. I suspect the easiest thing is to work 'em all low, then ask the middle strength station to move up the bands. The thought being that conditions might improve for the weakest station. If condx decline, we'll get the QSO with the two stronger stations.
Stuff on my plate:
Stuff on my plate:
- MSP 430 - work on tutorials
- 10G - start contacting other 10G stations to set up skeds for June
- 24G - get the filter tuned up
- Build an assembly out of Sigurd's DDS-60 / Softrock
Saturday, December 22, 2007
A day in the lab
I have a few AML 1900MHz amplifiers. They have 3 boards, one has the actual amplifier devices, one is a control board and one I can't readily tell. The control board has several parts that look like I can recycle:
On the ez430 front, Sigurd and Tommy have laid out an RS-232 interface. Sigurd is using an RS232 to TTL kit from NKC Electronics, and Tommy suggests a Maxim MAX3111E. Either way, I need to build up a board to interface the ez430 ro the outside world.
Spent a bit of time looking at my new 8-12.4 GHz mixer. It's an Anaren 7A0128, an eBay special. I hope to use it to mix 144.100 with 10224 to get 10368.100. At first blush, I put +7dBm LO (10224 from a microwave brick) and 0dBm IF (Yaesu FT-290RII) and looked at it with an HP 432. Almost nothing. Rats. What the heck. Hook it up to the HP 141T and see what I can see. There's a mixing product all right, but it's down around -30dBm. Need to look at it some more. I could really use a signal generator in the 432MHz range, or maybe 1296MHz. Too bad my 1296 transverter isn't finished :-( Maybe I ought to make an 1152 source and finish it!
In random link stumbling, came across Solder Smoke, where two hams podcast discussions about workbench projects. Also, W7ZOI's page, from the EMRFD book.
- Lattice ispLSI 2032 CPLD
- Atmel AT89S53 8 bit microcontroller
- 74HC541D Octal buffer, tri-state line driver
- MAX489 Low-Power, Slew-Rate-Limited RS-485/RS-422 Transceiver
- XM03AB LMC6464 Quad Micropower, Rail-to-Rail Input and Output CMOS Operational Amplifier
- LM2902D Single Supply Quad Operational Amplifier
- LT 031 16601 - can't find... house part?
- LT 024 364B14 - can't find... house part?
- JM05AB ADC1038 10-Bit Serial I/O A/D Converters with Analog Multiplexer and Track/hold Function [Discontinued]
- Summit S93X6Xs - really obsolete
On the ez430 front, Sigurd and Tommy have laid out an RS-232 interface. Sigurd is using an RS232 to TTL kit from NKC Electronics, and Tommy suggests a Maxim MAX3111E. Either way, I need to build up a board to interface the ez430 ro the outside world.
Spent a bit of time looking at my new 8-12.4 GHz mixer. It's an Anaren 7A0128, an eBay special. I hope to use it to mix 144.100 with 10224 to get 10368.100. At first blush, I put +7dBm LO (10224 from a microwave brick) and 0dBm IF (Yaesu FT-290RII) and looked at it with an HP 432. Almost nothing. Rats. What the heck. Hook it up to the HP 141T and see what I can see. There's a mixing product all right, but it's down around -30dBm. Need to look at it some more. I could really use a signal generator in the 432MHz range, or maybe 1296MHz. Too bad my 1296 transverter isn't finished :-( Maybe I ought to make an 1152 source and finish it!
In random link stumbling, came across Solder Smoke, where two hams podcast discussions about workbench projects. Also, W7ZOI's page, from the EMRFD book.
Thursday, December 20, 2007
Experimental Methods in RF Design

Experimental Methods in RF Design by Wes Hayward, Rick Campbell and Bob Larkin. I've been reading and reading and reading. What an incredible book. I've learnt so much stuff, it's hard to praise this enough. I have a good head for digital electronics, but RF is voodoo. These guys do a great job. I'm making a shopping list so I can start building some of the gear they so lovingly explain.
Way recommended!
Wednesday, November 21, 2007
TI MSP430 MCU
Texas Instruments has a cool microcontroller in their MSP430 line. It's the eZ430-F2013. It's a USB programmer/debugger and a teeny detachable board that has an F2013 on it. It's not only incredibly convenient to play with, it's only US $20! To top it off, you can buy a batch of 3 more detachable T2012 boards for another US $10! How can you beat that?
As a programmer, I found their IDE from IAR Systems a bit scruffy, but I've been using Eclipse for some time which makes comparisons iffy to say the least. I understand there's an Eclipse project that uses GCC to create MSP430 binaries... that should be interesting to track down. One issue with that is possible problems exchanging code with fellow hams. There's a group over in western Massachusetts taking a class using these things and it might be a good idea to standardise for the benefit of all.
The little USB stick has an LED on it (P1.0) and it seemed logical that my first project would be to flash the little bugger to make CW (Morse Code). My C is rusty, so I did it in assembler, by brute force. Might as well record that effort here for posterity.
Incredibly, this thing worked, and creates CW by flashing the LED!
I did a quick hack in C that looks like this:
This too, works although I really don't think I like the dots & dashes. I figure my next step is to use actual letters and convert them via an intermediate function call.
As a programmer, I found their IDE from IAR Systems a bit scruffy, but I've been using Eclipse for some time which makes comparisons iffy to say the least. I understand there's an Eclipse project that uses GCC to create MSP430 binaries... that should be interesting to track down. One issue with that is possible problems exchanging code with fellow hams. There's a group over in western Massachusetts taking a class using these things and it might be a good idea to standardise for the benefit of all.
The little USB stick has an LED on it (P1.0) and it seemed logical that my first project would be to flash the little bugger to make CW (Morse Code). My C is rusty, so I did it in assembler, by brute force. Might as well record that effort here for posterity.
;*******************************************************************************
;
; Play CW by flashing the LED
; intended for the MSP430-F2013 on the EZ430 USB development board
; P1.0 is an output port with an LED attached
;
; IAR workbench 4.09A
; 2007-11-18
;*******************************************************************************
#include "msp430.h"
;-------------------------------------------------------------------------------
NAME main
PUBLIC main
; Interrupt Vector
ORG 0FFFEh ; MSP430 RESET Vector
dc16 RESET
; Progam code
RSEG CSTACK
RSEG CODE
;-------------------------------------------------------------------------------
RESET MOV #SFE(CSTACK), SP ; Set stackpointer (256B RAM)
main mov.w #WDTPW+WDTHOLD,&WDTCTL ; Stop watchdog timer
bis.b #001h,&P1DIR ; Set P1.0 to output direction
clr.b &P1OUT ; reset P1.0
;-------------------------------------------------------------------------------
; flash the LED using the message you want
; this is an initial non-repeating preface
call #space
call #space
call #v
call #v
call #v
call #space
; this message repeats
loop call #c
call #q
call #space
call #d
call #e
call #space
call #k
call #c
call #two
call #h
call #i
call #z
call #space
call #space
call #space
; now generate a long "carrier"
mov.b #001h,&P1OUT ; LED on
call #space
call #space
call #space
call #space
call #space
call #space
call #space
call #space
call #space
call #space
mov.b #000h,&P1OUT ; LED off
call #space
jmp loop
;-------------------------------------------------------------------------------
;
; This section forms the various CW characters
;
;-------------------------------------------------------------------------------
; space
space call #pause
call #pause
call #pause
call #pause
call #pause
ret
;-------------------------------------------------------------------------------
a call #dit
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
b call #dah
call #dit
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
c call #dah
call #dit
call #dah
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
d call #dah
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
e call #dit
call #gap
ret
;-------------------------------------------------------------------------------
f call #dit
call #dit
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
g call #dah
call #dah
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
h call #dit
call #dit
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
i call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
j call #dit
call #dah
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
k call #dah
call #dit
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
l call #dit
call #dah
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
m call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
n call #dah
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
o call #dah
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
p call #dit
call #dah
call #dah
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
q call #dah
call #dah
call #dit
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
r call #dit
call #dah
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
s call #dit
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
t call #dah
call #gap
ret
;-------------------------------------------------------------------------------
u call #dit
call #dit
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
v call #dit
call #dit
call #dit
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
w call #dit
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
x call #dah
call #dit
call #dit
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
y call #dah
call #dit
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
z call #dah
call #dah
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
one call #dit
call #dah
call #dah
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
two call #dit
call #dit
call #dah
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
three call #dit
call #dit
call #dit
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
four call #dit
call #dit
call #dit
call #dit
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
five call #dit
call #dit
call #dit
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
six call #dah
call #dit
call #dit
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
seven call #dah
call #dah
call #dit
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
eight call #dah
call #dah
call #dah
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
nine call #dah
call #dah
call #dah
call #dah
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
zero call #dah
call #dah
call #dah
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
period call #dit
call #dah
call #dit
call #dah
call #dit
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
comma call #dah
call #dah
call #dit
call #dit
call #dah
call #dah
call #gap
ret
;-------------------------------------------------------------------------------
question call #dit
call #dit
call #dah
call #dah
call #dit
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
slash call #dah
call #dit
call #dit
call #dah
call #dit
call #gap
ret
;-------------------------------------------------------------------------------
;
; This section sets the individual elements and overall timing of each element
;
;-------------------------------------------------------------------------------
; dah
dah mov.b #001h,&P1OUT ; LED on
call #pause
call #pause
call #pause
mov.b #000h,&P1OUT ; LED off
call #pause
ret
;-------------------------------------------------------------------------------
; dit
dit mov.b #001h,&P1OUT ; LED on
call #pause
mov.b #000h,&P1OUT ; LED off
call #pause
ret
;-------------------------------------------------------------------------------
; inter-character gap
gap call #pause
call #pause
call #pause
call #pause
ret
;-------------------------------------------------------------------------------
; delay
; this sets the basic on or off time.
; Larger values mean slower CW
pause mov.w #040000,R15 ; max 65535
L1 dec.w R15
jnz L1
ret
END
Incredibly, this thing worked, and creates CW by flashing the LED!
I did a quick hack in C that looks like this:
// Flash the F2013 LED in CW
// IAR workbench 4.09A Kickstart
// TODO: translate character to CW
#include "msp430.h"
#include "string.h"
#define SHORT 3
#define LONG 7
int dot(void);
int dash(void);
int space(int);
int flash(char[]);
int main( void )
{
WDTCTL = WDTPW + WDTHOLD; // Stop watchdog timer
P1DIR |= 0x01; // Set P1.0 to output direction
for (;;)
{
flash("...- ...- ...- -.-. --.- -.. . -.- -.-. ..--- .... .. --.. ");
}
}
// takes an array of char and flashes that message
int flash( char chars[])
{char c;
for (int i=0; i<=strlen(chars); i++) {
c=chars[i];
switch (c)
{
case '.':
dot();
break;
case '-':
dash();
break;
case ' ':
space(LONG);
space(LONG);
break;
default:
space(LONG);
space(LONG);
break;
}
}
return 0;
}
int dot(void)
{
P1OUT = 0x01; // LED on
space(SHORT);
P1OUT = 0x00; // LED off
space(SHORT);
return 0;
}
int dash(void)
{
P1OUT = 0x01; // LED on
space(LONG);
P1OUT = 0x00; // LED off
space(SHORT);
return 0;
}
int space(int time)
{unsigned int i;
do
{time--;
i = 10000;
do i--;
while (i != 0);
} while (time != 0);
return 0;
}
This too, works although I really don't think I like the dots & dashes. I figure my next step is to use actual letters and convert them via an intermediate function call.
Subscribe to:
Posts (Atom)